Dremel Столик для фрезерования Instrukcja Użytkownika Pobierz pdf (Strona 5)

• Followthedust-relatednationalrequirementsforthematerials

you want to work with.

• Besuretoolisswitchedoffwhenpluggingin.

DURING USE

• Alwayskeepthecordawayfrommovingparts.

• Neverusethetoolwhencordorbase-plate(=protectiveguard)is

damaged; have it replaced by a qualiﬁed person.

• Keephandsandngersawayfromrouterbitwhentoolis

switched on.

• Incaseofelectricalormechanicalmalfunction,immediately

switch off the tool and disconnect the plug.

• Incasetherouterbitisblocked,resultinginjerkingforcesonthe

tool, immediately switch off the tool.

• Incaseofcurrentinterruptionorwhentheplugisaccidentally

pulled out, immediately switch off the tool in order to prevent

uncontrolled restarting.

• Donotapplysomuchpressureonthetoolthatitcomestoa

standstill.

ENVIRONMENT

DISPOSAL

Themachine,accessoriesandpackagingshouldbesortedfor

environmental-friendly recycling.

ONLY FOR EC COUNTRIES

Do not dispose of power tools into household waste!

According the European Guideline 2002/96/EC for Waste

Electrical and Electronic Equipment and its implementation

into national right, power tools that are no longer usable

must be collected separately and disposed of in an

environmentally correct manner.

APPLICATION ADVICE

• Usetheappropriaterouterbits.

• Forcutsparallelwiththesideofyourworkpieceusearipfence.

• Protectyourselfagainsttheeffectsofvibrationbymaintaining

the tool and its accessories, keeping your hands warm, and

organizing your work patterns.

ASSEMBLY

ATTACHMENT FOR USE WITH DREMEL ROTARY TOOL MODELS 300,

395, 398, 400, 4000.

ATTENTION: Read entire instruction manual carefully before using your

DremelShaper/RouterTable.Retaininstructionsforfuturereference.

ThisattachmentwillconvertDremelRotaryToolstoaShaper/Router

table for edge forming, routing, grooving, shaping, sanding, edges,

jointing, etc.

SeeFigure1:

BaseA

Carriage BoltB

ToolHolderC

Large KnobD

Depth Adjustment ScrewE

Nut - SquareF

Depth BracketG

Bracket ScrewH

PinI

Mounting ScrewJ

ThumbNutK

GuardL

SleeveM

Clamp Screw NutN

Washer #9O

Washer 4,8 mmP

FenceQ

Wedge Clamp ScrewR

WedgeS

MOUNT TABLE TO WORKBENCH

TheSHAPER/ROUTERTABLEcomesassembledreadytomountonthe

workbench. After determining table location, predrill the bench using a

3,2 mm diameter drill at the four mounting hole locations. Secure table

to the bench using the 4 wood screws, and washers. (Included with the

Shaper/RouterTable.)

SeeFigure2:

4 Wood Screws & WashersA

Use 50 mm x 100 mm as alternative mounting optionB

INSTALL ROTARY TOOL TO TABLE

SeeFigure3:

GuardA

FenceB

On/off switch must face forward so left-to-right motion will turn C

tool off.

Depth Adjustment ScrewD

Clamp KnobE

Make sure the power cord of the rotary tool is unplugged and 1.

install the required router bit.

Loosen the clamp knob and adjust the height of the tool holder to 2.

the lowest position.

Move the rotary tool from the underside in the tool holder and 3.

turn the nut on top of the tool holder to ﬁxate the rotary tool. Use

the open end spanner to fasten the nut.

OPERATING INSTRUCTIONS

CHANGING ROUTER BITS

Loosen the clamp knob and adjust the height of the tool holder to 1.

the lowest position.

Rotate the rotary tool so the shaft lock button can be operated 2.

through an opening in the tool holder.

Apply the shaft lock button and loosen the router bit.3.

Remove the router bit through the table and install another router 4.

bit.

Apply the shaft lock button and ﬁxate the router bit.5.

CUTTING DEPTH ADJUSTMENT

Loosen the clamp knob and turn the depth adjustment knob to set

cutting depth. Depth of cut will be the amount the bit extends above

the shaper/router table.

SeeFigure4:

Large KnobA

Depth of CutB

TableC

Depth Adjustment ScrewD

ToolHolderAssemblyE

Adjustment markings on the side of the tool holder facing outward are

marked in inches and millimeters. View the markings prior to starting

yourproject.Turnthedepthadjustmentknobtosetdesireddepth.To

ensure proper settings, rout and measure cut on scrap material.

SeeFigure5:Depth Adjustment Markings

Inches in 1/8 inch incrementsA

Millimeters in 5 mm incrementsB

1 2 3 4 5 6 7 8 9 10 ... 83 84

Dremel Столик для фрезерования Instrukcja Użytkownika Strona 5

Komentarze do niniejszej Instrukcji

Dremel Столик для фрезерования Instrukcja Użytkownika Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Narzędzia Dremel Столик для фрезерования